Issue link: http://alpine.uberflip.com/i/577795
4 AutoMill HP ™ P R O D U C T M A N U A L EN Disclaimer The information contained in this document is believed to be accurate in all respects but is not warranted by Alpine. The information is subject to change without notice and should not be construed in any way as a commitment by Alpine. Alpine assumes no responsibility for any errors or omissions in this document. Every reasonable effort is made to keep this document current, but in the event of discrepancy, Alpine engineering documentation, installation and service and safety procedures shall prevail. Copyright ©2016 by Alpine, a division of ITW Building Components Group Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of the publisher. 1. Introduction The Alpine AutoMill HP sets the bar for outstanding performance in the component manufacturing industry. Full automation for twenty-three moving axes increases setup speed and cutting accuracy. The five blades maximize the cutting range and throughput. The AutoMill HP is exceptionally versatile, using this user manual, setup the saw to meet the demands and flexibility required to maximize production efficiency. 1.1 Parts List 1.1.1 Motors, Gearboxes Alpine Part # (Motor) Alpine Part # (Gearbox) Axis 31422 30375 Angle 1 31422 30375 Angle 2 31422 30374 Angle 3 31422 30374 Angle 4 31422 30375 Angle 5 29114 24967 Head 1 U/D 29114 24967 Head 3 U/D 31422 24967 Head 5 U/D 29103 24967 Head 2 I/O 29103 24967 Head 4 I/O 29103 24967 Head 5 I/O 29114 30274 RHD U/D 29114 30274 LHD U/D 29103 24973 RHD I/O 29102 24974 RMC I/O 29103 24973 LHD I/O 29102 24974 LMC I/O 29102 33137 Carriage 29103 24973 Lumb Stop 29102 24969 LMC Drive 29102 24969 RMC Drive 29103 24969 LHD Drive 29103 24969 RHD Drive 1.1.2 Refuse and Incline Alpine Part # Description Note 20124 Belt Gearbox Incline & Refuse 72470 Motor Incline & Refuse (1/2HP, 1725RPM) 21993 Conveyor Belt Bearing Refuse Conveyor 26366 Key (5/16 X 3/8 X 6 ½) Key stock 24634 Belt Refuse (29" X 787") 74066 Roller Conveyor Used to reduce sag 14870 Incline idler roller Conveyor 14871 Incline drive roller Conveyor 73327 Bearing Incline Conveyor 8288 Cleated Belt Incline Conveyor (31" X 286") 17851 Diamond Top Belt Incline Conveyor (31" X 286") 1.1.3 Blades/Mandrels/Motors Alpine Part # Description Note 6395 20" Saw Blade Head 1 60174 32" Saw Blade Head 5 60124 18" Saw Blade Head 2,3,4 1968 FL HD SCREW, (5/16-18 x 1.25") Head 1,2,3,4,5 4128 Nylon Lock Nut (5/16-18) Head 1,2,3,4,5 1034 Blade Motor Head 1 74561 Blade Motor Head 2,3,4 74168 Blade Motor Head 5 3829 Mandrel Head 1 3830 Mandrel Head 2,3,4 3832 Mandrel Head 5 6014 Roll Pin Head 1,2,3,4 6027 Roll Pin Head 5 Throughout this manual, references are made to contact Alpine Equipment Customer Service. They can be reached at 800-521-9790 with any questions.