Issue link: http://alpine.uberflip.com/i/586848
64 alpineitw.com (800) 521-9790 For Product Substitutions … the ONLY APPROVED EQUAL ™ PRODUCT CODE REF NO DIMENSIONS (INCHES) NAIL SCHEDULE DESIGN LOAD UPLIFT LBS D W H WOOD I-JOIST HEADER JOIST NORMAL LBS MAX LBS MUI..9 MIU..9 2 1 ⁄2 Specify 9 Specify 16-16d 2-10d x 1 1 ⁄2 2270 2840 245 MUI..11 MIU..11 2 1 ⁄2 Specify 11 Specify 20-16d 2-10d x 1 1 ⁄2 2840 3550 245 MUI..14 MIU..14 2 1 ⁄2 Specify 13 1 ⁄4 Specify 22-16d 2-10d x 1 1 ⁄2 3125 3905 245 MUI..16 MIU..16 2 1 ⁄2 Specify 15 1 ⁄4 Specify 24-16d 2-10d x 1 1 ⁄2 3410 4005 245 MUI..18 MIU..18 2 1 ⁄2 Specify 17 1 ⁄4 Specify 26-16d 2-10d x 1 1 ⁄2 3695 4300 245 MUI..20 MIU..20 2 1 ⁄2 Specify 19 1 ⁄2 Specify 28-16d 2-10d x 1 1 ⁄2 3975 4300 245 MUI JOIST HANGERS Design Features… constant dimensional accuracy and precision controlled 90° angles ensure proper wood I-joist bearing (flat seat) and header connection and alignment. This design reliability is the result of using positive-control dies, automated machinery, skilled operators and prime quality galvanized steel. Two design styles are available for application and load bearing flexibility. Stock No. Design Configuration MUI Standard MUI( )R Reversed face flange (turned in) for 2 9 ⁄16" NET and larger joist sizes Wood I-Joist Sizes MUI: 1.56 series (2x) W = 1 9 ⁄16" 1.81 series W = 1 13 ⁄16" 2.06 series W = 2 1 ⁄16" 2.37 series W = 2 3 ⁄8" 2.56 series (3x) W = 2 9 ⁄16" 3.56 series (4x) W = 3 9 ⁄16" 4.12 series W = 4 1 ⁄8" 4.28 series W = 4 9 ⁄32" 4.75 series W = 4 3 ⁄4" 5.12 series W = 5 1 ⁄8" Material… 16 ga. galvanized steel for MUI joist hangers meets the specifications for schools and other public buildings. Loads… nailing schedule and design load capabilities are consistent with those obtained in independent laboratory tests. Design Features… MUI hangers are designed for high loaded commercial wood I-joist applications without web stiffeners that are usually required. There are optional joist nails for a total uplift load of 940 lbs. using 1 1 ⁄2" 10d nails. Note… web stiffeners and backing blocks may not always be required. Consult the engineered wood I-joist manufacturer for web stiffener and backing block requirements, and recommended nailing schedule for each. IMPORTANT Design loads are for joist hangers. They are NOT wood I-joist load values (see the Design Product catalog of the engineered wood I-joist manufacturer) W D 1³⁄₁₆" H 1¹⁄₄" MUI Positive Angle Nailing Angle Nailing Minimizes Wood Splitting of the Wood I-joist Flanges, While Permitting SUPERSPEED ® Nailing from a Better Angle MUI416 Onto Laminated Veneer Lumber (LVL) or Dimensional Lumber HBHQ HEAVY BEAM HANGERS (SCREW TYPE) Design Feaures… The HBHQ is a high capacity screw type (SUPERSPEED ® SDS 1 ⁄4 Drive Screws ™ ). Top Flange Hanger designed for use with LVL and PSL engineered wood products. The SDS screws provide for a lower profile compared to standard through bolts. Material. . Stirrup 7 ga. steel Top Flange 1 ⁄4" steel Finish… SUPERSPEED ® gray paint. Welding… is done by certified welders. Specials. . Available in standard width sizes and special height sizes. SUPERSPEED ® ( 1 ⁄4 x 3 SDS) Drive Screws ™ are furnished for all holes in the HBHQ hanger. Applications… all multiple hangers must be fastened together to act as one unit. Multiple header members may require additional fasteners at HBHQ header flange. Number and location of SUPERSPEED ® SDS 1 ⁄4 Drive Screws ™ to be the design responsibility of engineer of record. 3" L W H 6" 11 3 \4" HBHQ SUPERSPEED ® Drive Screws ™ Used With This Product For Product Substitutions … the ONLY APPROVED EQUAL ™ PRODUCT CODE REF NO DIMENSIONS (INCHES) SUPERSPEED ® SDS Z⁄v DRIVE SCREWS ™ DESIGN LOAD HEADER TYPE UPLIFT LBS 1.33 W H 11" Min L CARRYING BEAM (HEADER) SUPPORTED BEAM (PURLIN) DF/WL LBS PSL LBS HBHQ 3.62 EGQ3.62-SDS3 3 5 ⁄8 Specify 18 28-SDS 1 ⁄4-3 12-SDS 1 ⁄4-3 19800 18680 6365 HBHQ 5.50 EGQ5.50-SDS3 5 1 ⁄2 Specify 18 28-SDS 1 ⁄4-3 12-SDS 1 ⁄4-3 19800 18680 6365 HBHQ 7.25 EGQ7.25-SDS3 7 1 ⁄4 Specify 18 28-SDS 1 ⁄4-3 12-SDS 1 ⁄4-3 19800 18680 6365