Alpine

FRAMING CONNECTORS SPACEJOIST TE™ HANGERS FOR 320 JOIST 320 SERIES SINGLE 45o Skew Face Mount Top Flange Joist Height Fastener Type Fastener Type Header Joist Down Load 2 SUR/L310 14-16d 6-10dx1½ 1860 SUR/L310 14-16d 6-10dx1½ 1860 1555 SUR/L314 18-16d 8-10dx1½ 2395 1775 SUR/L314 18-16d 8-10dx1½ 2395 Joist Down Load 2 ITT39.25 6-10d 2-10dx1½ 1450 IUT310 8-10d 2-10dx1½ 890 ITT 311.25 6-10d 2-10dx1½ 1450 IUT312 10-10d 2-10dx1½ 1110 14" ITT314 6-10d 2-10dx1½ 1450 IUT314 14-10d 2-10dx1½ 16" ITT316 6-10d 2-10dx1½ 1450 IUT316 16-10d 2-10dx1½ 9¼" 11¼" Model Header Joist Model Variable Pitch Field Slope and Skew Adjustable Height Joist Height Fastener Type Down Load 2 Header Model Fastener Type Model Header Joist Fastener Type Down Load 2 Header Fastener Type Down Load 2 Model Joist Model Header Joist Down Load 2 9¼" THAI322 6-10d 2-10dx1½ 1835 LSSUH310 18-16d 12-10dx1½ 1600 VPA3 9-10d 2-10dx1½ 1230 11¼" THAI322 6-10d 2-10dx1½ 1835 LSSUH310 18-16d 12-10dx1½ 1600 VPA3 9-10d 2-10dx1½ 1230 6-10d 2-10dx1½ 1835 LSSUH310 18-16d 12-10dx1½ 1600 VPA3 9-10d 2-10dx1½ 1230 6-10d 2-10dx1½ 1835 LSSUH310 18-16d 12-10dx1½ 1600 VPA3 9-10d 2-10dx1½ 1230 14" THAI322 6 16" THAI322 6 3 320 SERIES DOUBLE Face Mount Top Flange Joist Height Model Fastener Type Joist Header Down Load 2 Adjustable Height Fastener Type Model Header Down Load 2 Joist Fastener Type Model Header Joist Down Load 2 9¼" LBV39.25-2 6-10d 2-10dx1½ 2035 MIU39-2 14-16d 2-10dx1½ 1860 Top Face 11¼" LBV311.25-2 6-10d 2-10dx1½ 2035 MIU311-2 16-16d 2-10dx1½ 2130 THAI-2 5 4-10d 2-10dx1½ 2020 LBV314-2 6-10d 2-10dx1½ 2035 MIU314-2 18-16d 2-10dx1½ 2395 THAI-2 5 4-10d 2-10dx1½ 2020 2035 MIU316-2 20-16d 2-10dx1½ 2660 14" 16" LBV316-2 6-10d 2-10dx1½ Refer to Simpson Strong-Tie® catalog Connectors For Composite Wood Products SIMPSON STRONG-TIE® — GENERAL NOTES 1. Highlighted hangers require web stiffeners at I-joist ends. Web stiffeners may be required for hangers that are not highlighted—contact your SpaceJoist TE representative for more information. 2. a) Loads listed are based on Douglas-Fir-Larch or Southern Pine species of LVL or solid sawn header. b) Download column represents floor loading at 100% duration. Other load durations may apply. Refer to the Simpson Strong-Tie® Composite Wood Products Connectors catalog for allowable increases. c) Minimum nail penetration required to achieve loads listed for face mount hangers: • 10d common min. penetration = 1¾" • 16d common min. penetration = 2" d) Top flange hanger capacities listed require a minimum header width of 3" for hangers using 10d common nails and 3½" for hangers using 16d common nails. e) When top flange hangers are supported by a SpaceJoist TE header, the following download applies with no further increase allowed: IUT • • f) 755 lbs. for ITT 895 lbs. for LBV • top nails: (4) 10d - 1½" • face nails: (2) 10d - 1½" • top nails: (4) 10d - 1½" • face nails: (2) 10d - 1½" When ITT hangers are supported by a single, less than 1½" thick, DF or SP LVL, the following load applies with no further increase allowed: • MIU 3. 4. 5. 6. 1235 lbs. for ITT hangers • top nails: (4) 10d - 1½" • face nails: (2) 10d - 1½" g) THAI hangers require a minimum of four (4) top and two (2) face 10d nails installed. If hanger height is less than 60% of joist height, potential joist rotation may occur—consult Simpson StrongTie® literature for additional information. Refer to the current Simpson Strong-Tie® Composite Wood Products Connectors catalog for hanger models and joist sizes not shown. THAI-2 hangers must be special ordered. Specify hanger seat width between 3-1/8" and 5-5/16". Joists taller than 14" require lateral restraint at the top chord when used with THAI hanger. Lateral restraint can be accomplished as described by the "Prevent Rotation" illustration on page 8 of the Simpson StrongTie® Composite Wood Products Connectors catalog or with blocking. ITT 15

• Cover