Issue link: http://alpine.uberflip.com/i/221331
HSH HEAVY SADDLE HANGERS Design Features . . accommodate heavier loads than the SH saddle hanger. Finish . . SUPERSPEED gray paint. Ordering/Specifying Information . . when specifying H1 and H2 dimensions, measure from underside of top channel to top of seat. HSH5 HHC HEAVY HINGE CONNECTORS . support HHC3 Design Features . the top of the bottom end of a glu-lam beam on another supporting HHC glu-lam beam of the same width and having the same top elevation. Seismic straps can be welded to side plate when H dimension is less than the minimum height requirement. Erection nail holes are provided for easy installation. Material . . bearing plate: ³⁄₄", 1", 1¹⁄₄" and 1¹⁄₂" steel. Welded to side plate of ³⁄₁₆" steel. Finish . . SUPERSPEED gray paint. Ordering/Specifying Information . . all HHC using three bolts should be ordered and identified as HHC3 (Example: HHC5-9 with three bolts, specify as HHC359). HHCT HEAVY HINGE CONNECTOR TABS .. ties on HHCM Design FeaturesThe standardized seismic is the hinge connector. HHCT standardized most commonly ordered HHC special. While the HHC3T design (as illustrated) is recommended, further modified alternates are available. HHCM design has slotted seismic ties as opposed pairs at the middle (centerline) of the HHC. T design denotes slotted tabs at top for HHC. M design denotes slotted tabs at middle (centerline) of HHC. Finish . . SUPERSPEED gray paint. Specify . . H dimension. Note . . machine bolts should be located in the top half on the slotted holes. See the HHC table for minimum three bolt tabs height design. Available in higher load values by increasing the D dimension. Contact factory for details. Ordering/Specifying Information . . all HHCM using four bolts in middle strap should be ordered and identified as HHC3/4M (Example: HHC5-9 with three bolt tabs and four bolt center straps, specify as HHC3/4M59). Special . . if the depth of the glu-lam is smaller than the minimum listed, adjust allowable load in direct proportion to height. 12³⁄₈" HCTS Shown with Round Holes 1 Side and Slotted Holes 1 Side HHCM HHC3T " " 2-25⁵⁄₈ 3-31⁵⁄₈ " HCTSR 4-37⁵⁄₈ HCTSR HCTSR (Shown with Slotted Holes) HHC3/4M HCTSR (HCTS Similar) CPT 50 HHC3T HCTS3 HCTS4 TYP 1¹⁄₂" 3" 3¹⁄₂" HHC3 CROSS PURLIN TIES Design Features . . Supports purlins on either side of a glu-lam beam to resist seismic forces. The heavy square bar section works in both tension and compression. Designed for installation in pairs, the heavy square bar helps with drilling alignment. Offset in center section provides clearance for purlin hanger stirrups. Requires a 2¹⁄₂" hole through the glu-lam beam for installation. Installation . . Hanger seat depth 4" are for CPT 18 and CPT 23. Hanger Seat depth 6" are for CPT 27 and CPT 38. Material . . B⁄," & ³⁄₄" Bar Stock Finish . . SUPERSPEED Gray Paint Glulam 2" Purlin HHC3M Top View Installed in Pairs ⁵⁄₈"or ³⁄₄" Typical L L1 L2 4" Typ - CPT18, 23, 27 4¹⁄₂" Typ - CPT38