Issue link: http://alpine.uberflip.com/i/126813
BC EBC BCO BCOB BCC BCT EBCL BCQ EBCQ End Beam Cap Design Features . . eleven configurations provide complete application flexibility. Stock No. Design Configuration BC Standard beam cap BC/EBC@90° Standard or end beam caps; post straps may be rotated 90° on special order, when beam is larger than post EBC End beam cap EBC9/EBC10 Use four beam bolts BCO Beam cap for welding to square tubes, pipes and other columns BCOB Cross beam connector, the result of back-to-back welding of two beam caps BCC Center beam caps with ³⁄₁₆" stirrups (2) welded to cap BCT "T" beam caps with ³⁄₁₆" stirrups (1) welded to cap EBCL "L" beam cap offset right or left with ³⁄₁₆" stirrups (1) welded to cap BCQ EBCQ NEW . . this design uses SUPERSPEED Drive Screws to provide faster installation and maintain the wood cross section. The SDS screws provide for a lower profile compared to standard through bolts. BCQ supplied with SUPERSPEED SDS ¹⁄₄" x 2" Drive Screws. BCQ46 Beam Cap End Type Cap = 8¹⁄₂" SUPERSPEED Drive Screws Used With This T Product Prod BCC EBC Rotated 90° 1³⁄₄" Unless Otherwise Specified BCO EBC66 Optional Welded ³⁄₄" x 12" Rebar As Shown To specify screw type beam caps use the letter "Q" after any style beam cap stock number. Example: BC 5 ¹⁄₄– 6 now is BC Q 5 ¹⁄₄– 6. "Q" stands for quick installation. BCT EBCQ46 Material . . BC, BCQ, EBC and EBCQ sizes: 3¹⁄₄", 4X and 6X are ³⁄₁₆" steel. All other sizes are ¹⁄₄" steel. Finish . . SUPERSPEED gray paint. Loads . . BCC, BCT and EBCL series: the side stirrups maximum allowable down load may not exceed 40% of the design load specified in the table for the standard product, and cannot exceed 10,665 lbs. The total sum of the loads may not exceed the design load table value . . Special . . also available in width of 7¹⁄₈" for use with LVL and PSL engineered wood products. Ordering/Specifying Information . . examples follow: BC46 – beam is the first number, 4 (3⁹⁄₁₆"); post is the second number, 6 (5¹⁄₂"). BCC66 – W3 & 4 = 6 (5¹⁄₂") and H2 & H3 = 6¹⁄₂" is a BC66 beam cap with 6 (5¹⁄₂") beams on each side with all beam seats flush. EBCL66L – W3 = 4 (3⁹⁄₁₆"), H2 = 8 is an EBC66 end beam cap with a 4x (3⁹⁄₁₆") beam on the left side (specify beam L for left side beam stirrup). The stirrup seat is 1¹⁄₂" below the cap seat. Specify the height of the stirrup from the top of the cap. The minimum H for the stirrup is 6¹⁄₂". The L dimensions may vary depending on W3. SC ESC BCO6 EBCL _ _ (L) BCOB66 BC66 ROTATED Straps can be rotated 90°, as shown SPLICE CAPS Design Features . . two convenient configurations, as listed below. Stock No. Design Configuration SC Standard splice cap ESC End splice cap SC series meets specifications for beamover-post connections or where splice occurs. Greater nail edge distances provide higher load values. Bolt holes provide optional installation with ¹⁄₂" bolts. Material . . 12 ga. galvanized steel. To order 16 ga. galvanized steel, add 16 to stock no. (Example: SC44-16). Ordering Information . . Example: SC46, beam is the first number, 4 (3 ⁹⁄₁₆"); post is the second number, 6 (5¹⁄₂"). 58 SUPERSPEED Drive Screws Used With This T Product Prod www.itwbcghardware.com - 800.521.9790 Splice Cap End Splice Cap SC66 ITW BCG Hardware