Alpine

ROOF JOIST/PURLIN HANGERS R Design Features . . of the R series offer a wide RA application flexibility, particularly to the panelized construction industry, including seven different versions: RH versions RHF (1) Standardversions (2) Skewed RHG (3) Offset versions (4) Saddle versions RHGF (5) Seat sloped versions (6) Top flange angled down versions (7) Top flange open/closed versions Additional design features provide easier, faster installation and greater load capacities and strength: where it is vital to construction needs. R – 2xs, 3xs and 4xs. RA – 3xs, 4xs, 6xs and double 2xs. RH – 4xs, 6xs and 8xs. RHG – glulam sizes. Material . . 12 ga., ³⁄₁₆" and ¹⁄₄" prime quality steel. R and RA series – 12 ga. and ³⁄₁₆" steel. RH series – 12 ga., ³⁄₁₆" and ¹⁄₄" steel. Loads . . maximum ultimate load values are calculated from independent laboratory tests conducted in accordance with code criteria, with a minimum safety factor of three. All nail holes must be filled with correct nails to achieve design loads! Uplift Values . . are the result of extensive testing programs conducted in conformity with criteria set forth by the ICC. (HNP) Hayward Nail Pattern is also available for additional uplift. To order Uplift sizes add "U" to stock No. (example RHU616). Finish . . SUPERSPEED ray paint. Design Dimensions . . H is sized to account for normal joist shrinkage. Specify if special H dimensions are required. W dimensions listed are for dressed timber widths as noted. Specify if special W dimensions are required. Ordering/Specifying Information: Skewed . . add SK to stock no., direction and angle of skew. (Example: R210X SKL 30°, R = Right, L = Left) Offset . . add OS to stock no. and direction of offset, left or right. (Example: R210X 0SL, R = Right, L = Left) Saddle . . add S to stock no. and width of supporting beams. (Example: R210X S = 5¹⁄₄) Sloped Seat . . add SL to stock no. and angle of slope (up or down). (Example: R210XSLU15°, D = Down, U = Up) Top Flange Angled Down . . add TFD to stock no., direction and angle. (Example: R210X TFDL15°, R = Right, L = Left) Top Flange Open . . add TFO to stock no. and angle. (Example: R210X TFO20°, C = Closed, O = Open) Any of the above are available in a combination hanger. (Example: Offset right, skewed 45° left, sloped down 15°). (R210X OSR/SKL45°/SLD15°). Skewed and Sloped Hangers . . available, specify angle (5O° max.) and whether left or right, up or down. Due to the infinite variety of custom orders, skewed hangers and sloped hangers are not code evaluated. Design loads of the nearest equivalent hanger should be used as a general guide, subject to specific engineering designs. Hangers may be welded to steel headers with ¹⁄₈" for R, ³⁄₁₆" for RA, and ¹⁄₄" for RH by 1¹⁄₂" fillet welds located at each end of the top flange. Weld-on applications produce maximum design load listed. Uplift loads do not apply to this application. TR TOP MOUNT HANGERS R410 Skewed Right (Welded) Top Flange Offset Pictured Left RA414 Saddle Version Angled Down Right H = High Side Sloped Down (Welded) RH414 Double Angled TR26N Design Features . . provide economical production framing with potential additional savings when hanger is pre-nailed onto carrying members. Positive control dies and prime quality galvanized steel ensure a perfectly flat 1-piece joist seat and 90° flanges for accurate header connections. Top flange design provides automatic self-jigging. 2 x 4 through 2 x 16. Material . . 18 ga. galvanized steel. Prongs . . no joist nailing . . provide faster, easier installation. Special . . for pole barn construction, use the TR24N or the TR26N with nailing into the joist, as needed. 22 www.itwbcghardware.com - 800.521.9790 ITW BCG Hardware

• Cover