Alpine

HEAVY-DUTY HANGERS (Double/Triple Wood I-Joists) BHV BHSV BEAM HANGERS Design Features . . seven versions to meet all specifications. (1) Standard versions (5) Top Flange Down versions (2) Saddle versions (6) Top Flange Open/Closed (3) Offset versions versions (4) Skewed versions (7) Seat Sloped versions The top flange nails are placed to avoid damage to the laminated headers. Nailers and ledgers must be 4x or larger, or should be evaluated by the designer. All fasteners must be used to achieve load values; verify that the header can receive all fasteners. March 2013 For Product Substitutions . . . the ONLY APPROVED EQUAL™ DIMENSIONS (INCHES) MATERIAL (INCHES) PRODUCT REF NO CODE ANGLE U-STRAP W H NAIL SCHEDULE HEADER DESIGN LOAD NORMAL LBS JOIST MAX LBS UPLIFT LBS 133% BHV GLTV 2⁷⁄₈ x 3¹⁄₈ x ¹⁄₄ x 10 5 x 7 ga Specify Specify 10-16d 6-16d 7360 7360 1370 BHSV HGLTV 2⁷⁄₈ x 6³⁄₄ x ¹⁄₄ x 12 6 x 7 ga Specify Specify 18-16d 6-16d 10780 10780 1370 BHV BHSV WOOD I-JOIST SIZES Single: 2 series (2x) 25 series 35 series 3 series (3x) 4 series (4x) W W W W W = = = = = 1⁹⁄₁₆" 1¹³⁄₁₆" 2³⁄₈" 2⁹⁄₁₆" 3⁹⁄₁₆" Double: 2 series (2x) 25 series 35 series 3 series (3x) 4 series (4x) W W W W W = = = = = 3¹⁄₈" 3⁹⁄₁₆" 4¹³⁄₁₆" 5¹⁄₈" 7¹⁄₈" Applications . . BHV and BHSV heavy-duty hangers accommodate typical structural requirements for that extra heavy load . . . these hangers are used for longer spans which require greater loads that satisfy the safety factor for sound building requirements. For weld-on BHV applications, the minimum required weld is a ³⁄₁₆" x 2¹⁄₂" fillet weld at each end of the header angle; BHSV requires a ¹⁄₄" x 2¹⁄₂" fillet weld at each end. Nails . . use 16d common nails. Finish . . SUPERSPEED gray paint. Skewed and Sloped Hangers . . available, specify angle (50° max.) and whether left or right, up or down. Due to the infinite variety of custom orders, skewed hangers and sloped hangers are not code evaluated. Design loads of the nearest equivalent hanger should be used as a general guide, subject to specific engineering designs. Options Available . . The BHV and BHSV hangers can be sloped and/or skewed. See the R series for ordering requirements. Note . . web stiffeners are normally required for double joist installation. Consult the engineered wood I-joist manufacturer for web stiffener requirements and recommended nailing schedule. BHSV BHV HBHQ BHV BHSV Typical Double Installation Typical Double Installation For Product Substitutions . . . the ONLY APPROVED EQUAL™ HEAVY BEAM HANGERS (SCREW TYPE) Design Feaures . . The HBHQ is a high capacity screw type ( SUPERSPEED SDS ¹⁄₄ Drive Screws). Top Flange Hanger designed for use with LVL and PSL engineered wood products. The SDS screws provide for a lower profile compared to standard through bolts. Material. . Stirrup 7 ga. steel Top Flange ¹⁄₄" steel Finish . . SUPERSPEED gray paint. Welding . . is done by certified welders. PRODUCT CODE W H 11" Min SUPERSPEED SDS ¹⁄₄ DRIVE SCREWS DESIGN LOAD HEADER TYPE L CARRYING BEAM (HEADER) SUPPORTED BEAM (PURLIN) DF/WL LBS PSL LBS UPLIFT LBS 133% HBHQ 3.62 EGQ3.62-SDS3 3⁵⁄₈ Specify 18 28-SDS¹⁄₄-3 12-SDS¹⁄₄-3 19800 18680 6365 HBHQ 5.50 EGQ5.50-SDS3 5¹⁄₂ Specify 18 28-SDS¹⁄₄-3 12-SDS¹⁄₄-3 19800 18680 6365 HBHQ 7.25 EGQ7.25-SDS3 7¹⁄₄ Specify 18 28-SDS¹⁄₄-3 12-SDS¹⁄₄-3 19800 18680 6365 HBHQ HBHQ 3" Specials. . Available in standard width sizes and SUPERSPEED (¹⁄₄ x 3 SDS) special height sizes. Drive Screws are furnished for all holes in the HBHQ hanger. Applications . . all multiple hangers must be fastened together to act as one unit. Multiple header members may require additional fasteners at HBHQ header flange. Number and location of SUPERSPEED SDS1/4 drive screws to be the design responsibility of engineer of record. L 11 " H 6" ITW BCG Hardware DIMENSIONS (INCHES) REF NO W SUPERSPEED Drive Screws Used Scr With This Product W www.itwbcghardware.com - 800.521.9790 43

• Cover